HumanCentric Soporte ajustable para computadora debajo del escritorio

A perfect fit for under my desk.

I was incredibly pleased with this computer mount. It’s easy to set up but heavy to mount one handed. It’s really best to have someone hold the mount up while you screw it in. Other than that, it holds your computer tower well off the floor so you can vacuum under it. I have a Dell Xp8900 and it perfect

Ok first.. I am not related, nor was I asked to leave a review. Second...I rarely leave reviews. Here's why I am leaving this review... This holder is made SO WELL that I can't imagine ever having an issue with it.... Provided it's installed correctly. The metal is much heavier than I expected! It turns as easy as it should without being sloppy. The hardware and little bumper pads are included along with fabulous instructions! It is better than described in the product info! Well done HUMANCENTRIC... WELL DONE! I HIGHLY RECOMMEND THIS PRODUCT!!

This is the only wall-mount option that is low-profile enough to work for my application. It's solid and works.HOWEVER, the height set and adjustment screws are all but inaccessible by hand when mounting to the wall. It's actually a ridiculous design; I'm not sure how the engineers expected the installer to access these screws.I had to put 3 bit extenders on my screwdriver just to reach the set screw, and the adjustment screw is still loose. Also you really have to hope that your case height lines up with one of the available adjustment holes, or else you'll have a large gap. I had my wife push up on the bottom with all of her might just to get it lined up while I used my Macgyvered screwdriver to get the set screw in.It looks great now, but I'm not looking forward to the day that I have …

I installed it two weeks ago and has been a very good solution for my standing desk, making easier the cable management and letting use the desk in sitting and standing height with no worries for the cables being pulled.The only cons I found is that I have a Cougar MG120-G case which has 210 mm (8.27 in) wide and I had to bend a little the top plate to hold it. To be fair, it claims support 7.75 in cases.In a few comments I read the screws aren't good for holding the whole piece but as my desk is high enough, I used the bigger screws (the wall ones).And last, it would be better if the bottom would be a little wider to hold all the base of the case.Apart from that, the material looks strong enough to not worry about it (I'll check it every week to avoid it falls) and I'm very satisfied …

Strudy. Well engineered. One improvement would make it perfect: Instead of one center hole to orient the lower device have four (4) pilot holes and an extra nut/bolt so that you can securely orient the product from moving ever so slightly left to right. As it stands now the center bolt will loosen eventually from pushing the on off switch of the PC and necessitate removal of the PC to tighten it. Otherwise its perfect. Oh also, although it's a US company would be nice if they made it at home vs. subcontracted in China. That "Made in [CCP] China" label urks me.

I have a Fractal Node 202 which is a small form-factor case, and thanks to the clever engineering of this product, it fit perfectly. I removed everything from my desk, mocked it up to the right hand side with enough room for wires (and enough room for some swivel), and then used a screwdriver to put in four screws to mount it to the desk. This came with a few felt tabs to keep the mount from scratching the case, thoughtfully, and I tacked those on and put the case in and tightened everything down. I will let any potential buyer know that the vertical portion is a bit tricky to get right, and I only have one out of two screws inserted in now and it works fine, but just do some testing to get everything to fit snuggly. But it's a great piece of kit that opened up a lot of space on my desk …

I really like this mount. I have a height-adjustable workstation, so it's mounted on the underside of the tabletop. It can be mounted from the side or from the top. A nice feature when mounted from the top is you're able to swivel the holder around, so you can face the PC at any direction that suits you. It also makes it convenient when you need to access the back of the PC for any reason. This mount adjusted perfectly for my PC (OptiPlex 7040 SFF). It comes with the little sticker bumpers to protect the PC's finish and helps in keeping the PC from moving. I don't normally take the time to write detailed reviews, but I feel this one deserved the attention. I felt pleased I received a good product at a decent price.